







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Paver Driveways in Hurst, TX: What They Cost and How Long They Take
Paver driveway installation in Hurst runs $7,000 – $18,000 for most residential lots in the 76053 and 76054 ZIP codes, and a typical job takes 4 to 7 working days from demolition to swept-in sand. You’re looking at a base excavation, a compacted aggregate sub-base, edge restraint, then a laid surface of interlocking pavers, and every one of those stages has to pass inspection before the next begins. Call (855) 912-5373 for a free on-site measurement and a written line-item quote.
How a Paver Driveway Goes In, Stage by Stage

Here’s the honest sequence we follow on a Hurst residential lot. It doesn’t skip steps, and the sub-base is where the money and the time actually go.
Day 1: Demo and layout
We pull out the existing slab, asphalt, or gravel, cut back the approach apron to the city right-of-way line, and mark the finished grades with a laser level. On Hurst’s 1960s – 1980s lots this is also when we find out what’s buried – older irrigation lines, a stray fence footing, sometimes a utility run that isn’t where the locate flags said. You decide the paver pattern and the slope (driveways need a minimum fall away from the garage door, roughly 2% to 3%, so water doesn’t pond against the threshold).
Days 1 – 2: Excavation and sub-base
This is the slow part, and it’s the part that determines whether the driveway is still flat in year ten. We excavate 8 to 10 inches deep for a vehicular application, then bring in 4 to 6 inches of crushed aggregate in lifts, compacting each lift with a plate compactor before the next. North Texas clay expands and contracts through the wet and dry seasons, so a properly compacted base and correct drainage are what keep pavers from heaving. You’ll see us on site with a compactor for most of a day here, and that’s normal.
Day 2 – 3: Edge restraint and bedding course
We set the edge restraint – a concrete curb or a spiked polymer edge – on the sides and at the apron. That restraint is what stops the field of pavers from creeping downhill over the years. Then a 1-inch bedding layer of coarse sand gets screeded flat and checked against the laser. You choose the edge style here: poured concrete curb looks tidier against a lawn, spiked edge is faster and cheaper.
Days 3 – 5: Laying the pavers
A 2,000 to 2,500 square foot Hurst driveway usually lays in two to three days with a two- or three-person crew. We set the pattern from a chalk line, cut the border and the apron returns with a wet saw, and keep checking the field for straightness as we go. This is the visible, satisfying stretch, but it only works if the previous two stages were right.
Days 5 – 7: Joint sand, compaction, and cleanup
We run a plate compactor over the finished field, sweep polymeric or regular joint sand into the joints, compact again, and top off. Polymeric sand costs more but resists washout and weeds – worth it on a driveway that takes hose water and rain runoff. Then we clean the site, walk the grades with you, and hand over the job. Final inspection gets scheduled at the end.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Options You’ll Actually Choose Between
Paver selection is where buyers get paralysis. Here’s what actually matters on a Hurst driveway, with the trade-offs spelled out.
- Concrete pavers (Cambridge Pavers, Oldcastle): The default for a reason. They hold color, resist freeze-thaw and Texas sun, and a cracked unit can be lifted and swapped. Expect $6 – $14 per square foot installed. The trade-off is upfront cost – higher than poured concrete per square foot.
- Clay brick pavers: Warmer, more traditional look that suits a brick-veneer ranch. Denser and heavier than concrete, so more labor to lay. Add 10 – 20% to the installed price. They can chip at the edges if a heavy truck is backed over them repeatedly, but they’re otherwise extremely durable.
- Permeable pavers: Open-joint or gapped systems that let water drain through a stone reservoir below. Worth considering if your Hurst lot has drainage problems or the driveway slopes toward the house. Costs 15 – 25% more because the base is deeper.
- Joint sand: Regular sand is cheaper and needs topping off every few years. Polymeric sand runs more but locks in place and resists washout and weeds – our default recommendation for a driveway.
- Edge restraint: Spiked polymer edge is fast and economical. Poured concrete curb adds cost but looks cleaner next to turf and holds up to string trimmers.
Thickness matters, too. A residential driveway wants 60mm to 80mm pavers over that compacted base, not the 40mm units sold for patios and walkways. If a contractor quotes a price that looks too good, ask what thickness they’re laying.
What Paver Driveways Cost in Hurst, TX

For most Hurst homes, a full paver driveway lands between $7,000 and $18,000. That range covers a standard two-car drive on a typical subdivision lot, including demo, base, pavers, edge, and joint sand. Here’s what pushes a job toward one end or the other:
- Square footage: A 400 square foot drive sits near the low end; a 900 square foot drive with an apron and a turnaround lands near the top.
- Existing surface: Tearing out a 4-inch slab costs more in haul-off and disposal than pulling up old gravel or asphalt.
- Base condition: Soft or poorly drained clay subgrade means deeper excavation and more aggregate – a real line item.
- Paver grade and pattern: Premium clay or permeable systems run higher; a simple running-bond concrete paver is the most economical.
- Access and grading: A tight Hurst lot where a skid steer can’t reach the work area means hand excavation and more labor hours.
A written estimate from us itemizes demo, haul-off, base depth, paver type and thickness, edge restraint, joint sand, and permit or inspection fees. What it typically excludes: relocating a utility meter or gas line, repairing a failed slab underneath, and landscaping restoration beyond basic grading. Ask for those to be quoted separately so nothing surprises you mid-job.
See the difference
Before
After
Before
After
Before
AfterWhat Hurst Homes Specifically Do to This Job
Hurst is a built-out inner-ring Mid-Cities suburb, and almost every paver driveway here starts as a remodel rather than new construction. The housing stock is dominated by 1960s – 1980s brick-veneer ranches on tight subdivision lots, and those lots bring two things: mature pecan and oak canopies that drop limbs and shade the work area, and a squeezed lot line that limits where equipment goes. The clay soils shift seasonally, so we plan for drainage and base depth from day one. Work on a property in the 76053 ZIP near the SH 183 corridor often means coordinating with city inspections on the approach apron – Hurst runs its own permitting, and the driveway apron where it meets the street is reviewed separately from the rest of the pour. Homeowners often pair this with Door Installation in Hurst if a new driveway prompts a front-entry refresh, or with Cabinets & Countertops in Hurst when the curb appeal project turns into a whole-house push. We handle Hurst and the surrounding Mid-Cities, and this is part of Driveway & Pavers work that can fold into a full Driveway & Pavers in Hurst project if you’re adding a walkway or patio at the same time.
Serving Hurst, TX – Our Local Coverage Area
We serve Hurst and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Paver Driveways in Hurst

Most paver driveways in Hurst take 4 to 7 working days from demolition to final compaction, weather permitting. Rain days add time because you can’t compact a wet base, and North Texas spring storms can push a job a day or two. Call (855) 912-5373 and we’ll give you a realistic start and finish window for your address.
Yes, most paver driveways in Hurst require a permit and an inspection, particularly anything touching the approach apron at the street or the property’s right-of-way line. Hurst runs its own city inspections, and we pull the permit and schedule the inspection as part of the job. Call (855) 912-5373 to talk through what your specific lot will need.
Sometimes, but it’s rarely the right call on a Hurst driveway. Laying pavers over an existing slab only works if the slab is sound, properly sloped, and gives you enough clearance at the garage threshold. On 1960s – 1980s driveways we usually find cracking or settling that means removing it. Call (855) 912-5373 and we’ll assess whether an overlay is even an option.
Paver driveway installation in Hurst typically runs $7,000 – $18,000 for a two-car drive on a standard lot. The number moves with square footage, base depth, paver grade, and how much demolition your existing surface requires. Call (855) 912-5373 for a written line-item quote – estimates are free.
Every paver driveway we install is covered by our 730-Day Done Right Promise – if it’s not done right, we make it right. That covers workmanship on the base compaction, edge restraint, and installation. Manufacturer warranties on the pavers themselves vary by product. Ask for the written terms before you sign so you know exactly what’s covered.
Get a Free Paver Driveway Estimate in Hurst
We’ll come out, measure your drive, check the base and drainage, and hand you a written line-item estimate for paver driveways in Hurst – no vague pricing, no change orders after the fact. Upfront pricing, background-checked technicians, and 0% financing for 18 months is available if you’d rather spread the cost. Call (855) 912-5373 and a live person will set up your free on-site estimate.
Written by the team at Groundwork Construction Co.












