







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Chain Link Fence in Hurst, TX: What the Job Involves and What It Costs
A chain link fence in Hurst, TX typically runs $3,500 – $9,000 for a standard residential lot, and most jobs are finished in 2 – 4 days once the layout is set and the utilities are marked. That number covers posts set in concrete, top rail, tension wire, fabric, and a walk gate; the spread comes from linear footage, height, gauge, and how much old fence has to come out. Call (855) 912-5373 and we’ll walk your Hurst property and put real numbers on paper. Estimates are free.
How We Build a Chain Link Fence in Hurst, Step by Step

The day-to-day reality of this job matters more than the sales pitch, so here’s the actual order of operations and where you make decisions.
- 1
Day 1, morning: call 811 and walk the line. Before a single post goes in, Texas law requires utilities to mark the ground. We schedule that ticket, then meet the rep on site. This is also where we finalize gate placement and corners with you. Decide now, not later: where the walk gate lands, whether you want drive gates, and whether the fence runs inside or on your property line. On Hurst’s tight, mostly-built-out lots, a few inches of layout matters, and we measure the setback before we dig.
- 2
Day 1, afternoon: demolition and layout. Old fence comes down, posts get pulled, and we set the new corners and gate posts in concrete first. Concrete needs a cure window, so those posts sit overnight. Most of the cutting and fabricating happens here.
- 3
Day 2: line posts, top rail, and tension wire. The remaining posts get set, the top rail is cut and fitted, and tension wire goes in along the bottom. This is the stage where a homeowner decision shows up: 6-foot versus 4-foot height, and whether the bottom rail goes in to keep dogs from pushing under. We confirm the gate hardware and latch style before the fabric unrolls.
- 4
Day 3: fabric, stretching, and gates. Chain link fabric is hung, stretched with a come-along so it doesn’t sag over the years, and tied off. Gates get hung, plumbed, and cycled a few times to confirm the latch lines up. This is the call where you should be home if you can be.
- 5
Final: cleanup and walkthrough. Concrete touchdown, scrap and old fence hauled off, and a full cycle of every gate with you standing there. If anything doesn’t latch clean or sits low, it gets corrected before we leave. All of it sits under our 730-Day Done Right Promise, and if something’s not done right, we come back and make it right.
If the fence is part of a bigger yard project, this can roll into a Fence Installation in Hurst scope so grading and layout are handled together.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Options You’ll Pick Between on a Chain Link Fence
Every choice here is a trade-off between cost, life span, and how it looks from the street. Here’s what actually gets chosen on Hurst jobs:
- Gauge: 11.5 vs. 9. 11.5-gauge fabric is the standard homeowner grade. It’s the right call for privacy, pet containment, and yard definition, and it’s where most budgets land. 9-gauge is a thicker wire that resists bending and dog-chewing better; it costs more per foot but earns that back if you’ve got a dog that leans on the fence or kids who play against it.
- Height: 4 ft vs. 6 ft. 4-foot is cheap, open, and code-friendly nearly everywhere. 6-foot is the common pick for pets and pool barriers (pool spacing is regulated by code, so we confirm the local requirement before quoting).
- Vinyl-coated vs. galvanized. Bare galvanized is the least expensive and takes on a dull grey patina over the years. Vinyl-coated (black, green, or brown) costs a bit more and holds color, which is a real factor in North Texas sun that bakes untreated metal light grey. Coated also blends better against a brick veneer ranch house where a bright silver fence looks loud.
- Gates and hardware. A walk gate is standard. Drive gates, double gates, and self-closing latches for pools cost more and need heavier posts, so they get planned in the layout stage, not tacked on.
- Posts: standard vs. heavier wall. Standard schedule posts are fine for a normal yard. Heavier posts matter on corners, gate posts, and fences running along a line that catches wind, which is a genuine consideration in this part of Texas.
What a Chain Link Fence Costs in Hurst, TX

The working range is $3,500 – $9,000 for a typical residential lot in Hurst. Here’s roughly how a line-item quote breaks down:
- Standard 4-ft chain link, typical lot: $3,500 – $5,500
- 6-ft chain link with one walk gate: $5,000 – $7,500
- 6-ft with drive gate, heavier posts, vinyl-coated: $6,500 – $9,000
- Remove and haul off an old fence: typically $400 – $900 depending on length and how much concrete comes out
The variables that push you to the low or high end are linear footage (obviously), height, wire gauge and coating, gate count and weight, and site access. On Hurst’s older ranch lots, mature tree lines and tight side yards can slow a run down and add labor. Add footing work if the ground is hard-packed clay or if old concrete footings have to be broken out and removed.
When we write your estimate, it’s line-item and it’s what you’ll pay: the number you see is the number you pay. What’s included is the fence, posts, concrete, hardware, and cleanup. What’s not included by default is old fence removal (quoted separately), grading, and any permit fee, which we’ll itemize and tell you whether Hurst requires one for your scope. Call (855) 912-5373 for an exact quote.
See the difference
Before
After
Before
After
Before
AfterWhat Hurst Yards Specifically Do to a Chain Link Fence Job
Hurst is a mostly-built-out inner-ring Mid-Cities suburb, and that changes this job in ways a new-build lot doesn’t. Almost all the work here is on 1960s – 1980s brick-veneer ranches and small two-story traditional homes on tight subdivision lots in the 76053 and 76054 ZIPs. Tight lots mean property lines are close together, side yards are narrow, and the fence line often runs right up against a neighbor’s existing fence or a shed. On the older ranch properties, mature pecans and oaks overhang fence lines, so we routinely deal with limb damage to an existing run and roots that make post digging slower, especially when utility paths run close to the fence line. That’s also the reason we pull an 811 ticket first. The good news is that Hurst’s own city inspection process is well-worn for this kind of work, and most homeowners pair a new run with a yard cleanup or a related project like Door Installation in Hurst on the same schedule. We cover Hurst regularly and know the drill on these established streets.
Serving Hurst, TX – Our Local Coverage Area
We serve Hurst and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked: Chain Link Fence in Hurst

Most chain link fences here take 2 to 4 working days from the day utilities are marked. Day 1 is layout and corner post work, Day 2 is line posts and rail, Day 3 is fabric and gates, with a small buffer for hard ground or old concrete. Call (855) 912-5373 to schedule your free estimate and we’ll give you a firm timeline for your lot.
Permit requirements depend on the height and placement of the fence, and we’ll tell you in writing whether your specific run needs one. That’s a common trap – a homeowner gets a vague “you might need a permit” and then a fine later. We check your scope against the city requirement, include the permit line on the estimate if it applies, and pull it for you. Call (855) 912-5373 to walk through your property.
Yes – chain link is one of the least disruptive fences to install because it only requires localized post holes rather than a continuous trench. We hand-dig or auger individual post holes, set concrete, and leave the grass between them alone. If there are irrigation lines or buried utility paths running under the fence line, the 811 ticket and a walkthrough catch those before a shovel hits the ground. Call (855) 912-5373 to book the walkthrough.
Expect $3,500 – $9,000 for a standard residential lot, with the low end being 4-foot galvanized and the high end being 6-foot vinyl-coated with drive gates and heavier corner posts. Old fence removal, footing work, and permit fees are itemized separately. Call (855) 912-5373 – estimates are free and there’s no pressure.
Every chain link fence we build sits under the 730-Day Done Right Promise – if it’s not done right, we make it right. That covers workmanship and installation, including posts, gates, and stretching. It’s one of the longest workmanship guarantees we offer on the exterior of a home. Call (855) 912-5373 to schedule your free estimate.
Ready for a Real Estimate on Your Chain Link Fence?
We’ll walk your Hurst property, measure the run, confirm utilities and permit needs, and hand you a written line-item estimate at no cost and no obligation. If the fence is part of a wider yard project that includes your Fence Installation scope or ADU Site Prep & Utilities in Hurst, we’ll quote it all on one schedule. Calls are answered by a live person, 24/7. Call (855) 912-5373 to schedule your free estimate.
Written by the team at Groundwork Construction Co.












