







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Asphalt Driveways & Resurfacing in Hurst, TX
Most asphalt driveway work in Hurst runs $3,500 to $9,000 for new paving and $250 to $700 for a reseal, and a full mill-and-overlay typically takes two to three days once the weather cooperates. Asphalt Driveways & Resurfacing means tearing out or grinding the failed surface, rebuilding the base where it’s gone soft, compacting, and laying hot-mix asphalt at the right depth for Texas heat. Call (855) 912-5373 for a free on-site estimate and we’ll tell you whether you need a seal, an overlay, or a full replacement.
How Asphalt Driveways & Resurfacing Actually Unfolds

Hot-mix asphalt isn’t a same-week product. The schedule depends on plant availability and the ground temperature, so here’s the real sequence we run in Hurst.
Stage 1: On-site measure and subgrade check (about an hour). We probe the base with a spade and walk the edges to see where it’s pumping or cracked. You decide right here whether you’re doing a seal coat, a mill-and-overlay, or full-depth replacement. If the base is failing, an overlay just buys you two years.
Stage 2: Demo and haul-off (day one, half to full day depending on square footage). A typical Hurst ranch driveway of 600 to 900 square feet grinds out in a few hours. We haul the millings to a recycler and reject anything that isn’t clean. You’ll want to move cars off the drive the night before.
Stage 3: Base repair and grading (day one or two). This is where the cost lives. Soft spots get dug out, replaced with crushed limestone or flex base, and compacted in lifts. We re-grade so water sheds toward the street instead of pooling against the garage slab, which is a real problem on Hurst’s older lots where the ground has settled.
Stage 4: Paving (two to four hours). Hot-mix arrives at 280 to 300 degrees and gets laid at 2 inches compacted for a residential drive, 3 inches if you park a heavy truck or trailer. We roll it while it’s hot, then finish the edges. You can’t drive on it for 24 to 48 hours.
Stage 5: Cure and seal schedule (two to twelve months later). Fresh asphalt needs to cure before it’s sealed, usually a full season. We put the seal date in writing so you know when to call. This is the step most homeowners skip and the reason so many Hurst drives crack early.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Asphalt Options You’ll Choose Between
- Seal coat only: $250 to $700 and buys you two to three years of protection. Right call when the surface is intact and you’re just fighting sun oxidation. Wrong call if there are structural cracks.
- Mill-and-overlay: Grind off the top 1.5 to 2 inches and lay fresh asphalt on top. Cheaper than a tear-out if the base is sound. Doesn’t fix drainage problems or a failing subgrade.
- Full-depth replacement: New base plus new surface. The only honest answer when the base has failed. Most Hurst drives over 25 years old land here.
- Hot-mix vs. cold patch: We use hot-mix, period. Cold patch is a temporary fix that’ll rut in a North Texas summer.
- Standard vs. fiber-reinforced mix: Fibers add a few hundred dollars and reduce cracking in areas with heavy sun exposure. Worth it on longer drives.
What Asphalt Driveways & Resurfacing Costs in Hurst, TX

Expect $3,500 to $9,000 for new asphalt paving on a typical Hurst driveway. A seal coat runs $250 to $700. A full replacement combining demo, base repair, and new asphalt lands in the $5,000 to $14,000 range.
What pushes a job toward the high end:
- Size: Every additional 100 square feet adds roughly $400 to $700.
- Base condition: Soft subgrade or failed base can add $1,500 to $3,000 in excavation and new flex base.
- Drainage corrections: Re-grading away from the garage or adding a swale adds $500 to $1,500.
- Access: A drive tucked behind a fence or under low pecan canopy slows the equipment and adds labor.
- Permits: Hurst requires a permit if you’re cutting into the right-of-way or changing the approach apron. That adds cost and time.
Our written estimate includes the base prep depth, asphalt thickness, compaction, and haul-off. It does not include any permit fees, curb or apron repair, or landscaping restoration unless we list them.
See the difference
Before
After
Before
After
Before
AfterWhat Hurst’s Older Lots Do to This Job
Nearly every driveway we touch in Hurst’s 76053 and 76054 ZIP codes sits on a 1960s or 1970s ranch lot, which means the original asphalt has already been sealed, patched, and re-sealed at least once by somebody. We find alligator cracking radiating from a settled spot, or crumbling edges where roots have lifted the base. The mature pecan and oak canopy helps with shade, but roots push under the drive and limbs drop onto it in spring storms. We also run into expansive clay that swells and shrinks with the season, so a drive that looked fine in November can show new cracks by July. Hurst’s own city inspections apply when we’re modifying the approach apron, and tight lot lines mean we can’t always swing a full-size paver, so we plan equipment access before we schedule. If you’re overhauling the front of the property, homeowners often pair this with Chain Link Fence in Hurst and treat the driveway as part of a full Driveway & Pavers in Hurst project. Every quote is backed by our 730-Day Done Right Promise. You can see the rest of our Driveway & Pavers work across Hurst, and if you’re planning a build-out at the back of the lot, ADU Site Prep & Utilities in Hurst shares the same grading and access work.
Serving Hurst, TX – Our Local Coverage Area
We serve Hurst and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked About Asphalt Driveways & Resurfacing in Hurst

Most jobs finish in two to three working days from demo to final roll, plus 24 to 48 hours off the surface before you drive on it. Weather is the wild card; asphalt needs ground temps warm enough for the mix to compact properly, so a cold snap pushes the schedule. Call (855) 912-5373 and we’ll give you a realistic window.
You need a permit if the work changes the curb cut, approach apron, or right-of-way, and a straight replacement within your property usually doesn’t. Hurst runs its own city inspections, so the rules differ from neighboring Bedford or North Richland Hills. We pull the permit and coordinate the inspection as part of the job.
Yes, if the base is sound and the cracks aren’t structural. A mill-and-overlay grinds off the top 1.5 to 2 inches and lays fresh asphalt, which saves money and days. If our subgrade probe shows pumping or a failed base, an overlay is wasted money, and we’ll tell you so in writing.
Seal coats run $250 to $700, new asphalt paving $3,500 to $9,000, and a full replacement with base work $5,000 to $14,000. Size, base condition, and drainage corrections move the number most. Call (855) 912-5373 for an exact quote; estimates are free and pricing is upfront.
Every job is covered by our 730-Day Done Right Promise. If it’s not done right, we make it right. We hand you the guarantee in writing before work starts, and the crew that shows up is background-checked and uniformed. Call (855) 912-5373 to schedule.
Get a Free Asphalt Estimate in Hurst
We’ll walk the drive, probe the base, and hand you a fixed price with the asphalt depth and base prep spelled out. No change orders, no surprises. Reach a live person at (855) 912-5373 any time, day or night. Most estimates take under an hour on site and you’ll have a written number back within a day.
Written by the team at Groundwork Construction Co.












