







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Chain Link Fence in Richland Hills, TX: What It Costs and How Fast It Goes Up
A chain link fence in Richland Hills typically runs $3,500 – $9,000, with most residential lots landing in the $4,200 – $6,800 range depending on linear footage, height, and whether you’re replacing an old fence or fencing open ground. A standard 4-foot residential run goes up in one to two days once materials are on site; taller 6-foot fences with privacy slats take two to three. Call (855) 912-5373 for a free on-site measurement and a written line-item quote.
How a Chain Link Fence Goes In, Start to Finish

Every job runs the same five stages. Here’s what actually happens and when you make decisions.
- Site walk and utility locate (day 1). We measure the run, mark corners and gates, and confirm the property line against your survey. Before any digging, TX811 gets called for underground utility marking, which takes two to three business days in this part of Tarrant County. On tight 76118 lots, we also check where the fence line sits relative to your neighbor’s existing fence or shed.
- Layout and demolition (day 1, after locate clears). Old fencing, posts, and concrete footings come out. A 150-foot removal typically adds half a day. You decide here whether the old chain link gets hauled off or you keep the panels for scrap.
- Post setting (day 1 – 2). Line posts go in at 8 to 10 feet on center, terminal posts at corners and gates, each set in concrete. This is where the fence either holds up for 20 years or leans after the first clay-soil shift. Posts cure overnight before any tension is applied.
- Top rail, fabric, and tension (day 2 – 3). Top rail gets cut and coupled, fabric is stretched and tied off with tension bars and bands. You choose fabric height, gauge, and whether you want a bottom tension wire for dogs.
- Gates and walkthrough (day 3). Gate frames hang, latches align, and we walk the whole run with you. Any sag, gap, or loose tie gets fixed before we leave.
Our technicians have up to 12 years of experience setting posts in North Texas clay, and every job is covered by our 730-Day Done Right Promise. If a post leans or a gate drops in that window, we come back and make it right.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Choices That Actually Change Your Chain Link Fence
Chain link is a simple product, but the spec decisions are where a fence either lasts or looks tired in five years. Here’s what you’re picking between:
- Fabric gauge. 11.5-gauge is the residential standard and holds up fine for most yards. 9-gauge is heavier, resists dog damage and hail better, and adds roughly 15 – 25% to material cost. Worth it if you have large dogs or a corner lot with kids.
- Height. 4-foot is code-typical for front and side yards in Richland Hills; 6-foot is the common backyard privacy height. Going taller usually needs a neighbor conversation and, in some cases, a permit.
- Coating. Galvanized is the budget choice and rusts faster in humid stretches. Vinyl-coated (typically green or black) costs more up front but adds years in our climate and looks less industrial against a brick ranch house.
- Privacy slats. Inserted into the fabric for screening. Costs roughly $1.50 – $3.00 per linear foot installed and cuts wind load noticeably, so post spacing and concrete volume have to be spec’d for it.
- Gate hardware. Residential pivot hinges versus self-closing kits. Self-closing matters if you have a pool or a dog that bolts.
Post material matters too. Schedule 20 galvanized pipe holds up better than the thin-wall tubing some outfits use, especially where clay movement stresses the concrete collar.
What a Chain Link Fence Costs in Richland Hills, TX

Expect $3,500 – $9,000 for a typical residential chain link fence in Richland Hills. Here’s what moves the number:
| Line item | Typical range |
|---|---|
| 4-foot galvanized, 150 linear feet | $3,500 – $5,000 |
| 6-foot vinyl-coated, 150 linear feet | $5,200 – $7,400 |
| Privacy slats (added) | $1.50 – $3.00 / linear ft |
| Old fence removal and haul-off | $300 – $800 |
| Single walk gate | $250 – $550 |
| Double drive gate | $600 – $1,400 |
The variables that push a job to the high end: total linear footage (a quarter-acre lot versus a half-acre lot is a real jump), number of corners and gates, heavy clay digging that requires a gas auger or rock bar, vinyl coating versus bare galvanized, and whether old concrete footings have to be broken out. What’s included in our written estimate: posts, fabric, top rail, tension bars, concrete, gate hardware, haul-off, and permit if one is required. What’s typically not: property line survey (we use yours), landscaping restoration beyond basic seed and straw, and any fence work on a neighbor’s side of the line.
Upfront pricing, no surprises. The number in your estimate is the number you pay.
See the difference
Before
After
Before
After
Before
AfterWhat Richland Hills Lots Specifically Do to a Chain Link Fence
Richland Hills is a small, fully built-out inner-ring suburb, and that changes this job. Lots in 76118 are mostly tight, platted in the 1950s – 1970s, and the housing stock is mid-century brick ranch with pier-and-beam or slab foundations. When we set posts along a property line here, we’re almost always working within a few feet of an existing fence, a shed, or a neighbor’s mature pecan. Post spacing and gate swing have to be measured, not assumed.
The other local reality is the clay. The shrink-swell soil across Richland Hills and neighboring Haltom City expands and contracts with the drought-and-rain cycle, and alone that will heave a badly set post within a couple of seasons. We set terminal posts deeper and use a wider concrete collar than the minimum, which is the difference between a fence that stays plumb through a dry summer and one that doesn’t. If a fence run is part of a Fence Installation in Richland Hills scope that includes grading or a new shed pad, we coordinate the two so the post line isn’t disturbed after the fact.
Permitting runs through the city, and a fence over 6 feet or one on a corner lot may require a permit and inspection. If you’re also planning a backyard structure, homeowners often pair a chain link perimeter with ADU Site Prep & Utilities in Richland Hills so the fencing and utility trenching happen in one pass rather than tearing up finished work.
Common Chain Link Fence Scenarios We See in Richland Hills
Most calls we get in Richland Hills fall into four buckets:
- Replacing a 20-plus-year-old rusted run. The posts have rusted through at the concrete line and the fabric is sagging. We tear out, reset, and rebuild in two to three days.
- Fencing an open backyard after a purchase. New homeowners on a mid-century lot need a full perimeter, often with one drive gate. Usually one to two days.
- Adding a dog run or side-yard barrier. Short runs, 6-foot height, with a self-closing gate. Half-day job.
- Fencing a corner lot for privacy or pool code. Taller run, more corners, often with privacy slats. Two to three days and, typically, a permit.
Serving Richland Hills, TX – Our Local Coverage Area
We serve Richland Hills and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked: Chain Link Fence in Richland Hills
Most residential chain link fences run one to three days on site, plus a two-to-three-day wait for the TX811 utility locate before digging begins. A standard 150-foot 4-foot fence is typically one to two days; a 6-foot run with privacy slats and gates takes two to three. Call (855) 912-5373 to schedule your free estimate.
Fences at or below 6 feet in a standard residential yard usually don’t require a permit, but corner lots, taller fences, and some HOA subdivisions do. We check the requirement for your specific address before we order materials and pull the permit if it’s needed. Call (855) 912-5373 and we’ll confirm what applies to your lot.
In most cases, yes. Post holes are augered individually and the disturbed area is small, roughly the diameter of the concrete collar per post. If the ground is packed clay or there’s an existing fence panel to remove first, minor turf repair is normal, and we spread seed and straw on the post line when we finish. Call (855) 912-5373 for an exact quote – estimates are free.
Residential chain link in Richland Hills runs $3,500 – $9,000, with most projects landing in the $4,200 – $6,800 range. Footage, height, coating, gates, removal of an old fence, and clay-digging conditions push the number up or down. Call (855) 912-5373 for an exact quote – estimates are free.
Every chain link fence we install is backed by our 730-Day Done Right Promise. If a post leans, a gate drops, or the workmanship fails within that window, we come back and make it right. Material warranties come from the manufacturer and we pass them through to you. Call (855) 912-5373 with questions about coverage.
Get a Free Estimate on Your Chain Link Fence in Richland Hills

Call (855) 912-5373 and a live person answers, day or night. We’ll set a time to walk your property, measure the run, check the property line, and hand you a written line-item estimate with the post spacing, gauge, and gate hardware spelled out. No pressure, no vague bids. If the project grows into a broader scope, our fence installation service covers it, and homeowners finishing the backyard often pair this with Door Installation in Richland Hills. We serve all of Richland Hills and the surrounding Tarrant County area.
Written by the team at Groundwork Construction Co.












