







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Chain Link Fence in Kennedale, TX: What the Job Actually Involves
A chain link fence in Kennedale, TX runs $3,500 – $9,000 for a typical acreage-lot install, with most residential jobs landing in the $4,200 – $6,800 band once gates, corners and a proper drive gate are counted. A standard 150 – 300 foot run takes one to three working days from layout to tensioned fabric, assuming the ground is clear and Kennedale’s own inspection schedule lines up. Call (855) 912-5373 for a free on-site estimate.
Day by day: how we build a chain link fence in Kennedale

Chain link is one of the few fence types where the whole job is genuinely visible from the first hour. Nothing hides behind brick or pickets. That’s good news, because it means you can see exactly what you’re paying for and catch problems before the crew packs up.
- Stage 1 – layout and utility locates (half a day). We walk the property line with you, mark corners and gate posts, and call in the 811 locate before anyone puts a shovel in the ground. On larger Kennedale lots where a shop or barndominium sits well back from the street, we also confirm the fence line doesn’t cross buried water, septic or electrical runs servicing those outbuildings. This is the stage where you decide the exact line, gate swing direction, and where the drive gate lands.
- Stage 2 – hole digging and post setting (day 1). Line posts go in at 8 to 10 foot spacing, terminal posts at every corner and gate, and each hole is set in concrete to below the frost-relevant depth (North Texas doesn’t freeze deep, but our clay does move, so we go wide and deep enough to resist shrink-swell). You’ll smell the concrete and see the string lines. Nothing gets rushed here.
- Stage 3 – top rail, tension bands and fabric (day 2). We set top rail through the line post loops, hang tension bars at each terminal, and pull the chain link fabric to tension with a come-along. You decide at this point whether you want the fabric on the inside or outside of the framework, and whether you want a bottom tension wire to stiffen the base against a dog leaning on it.
- Stage 4 – gates and hardware (day 2 into day 3). Walk gates and drive gates get hung, sag bars go on the wide ones, and we set the latches and hinges. On properties with a detached shop or a rear driveway, a double drive gate is often the piece that gets the most use, so we spend real time getting the sag out before we tension anything to it.
- Stage 5 – walkthrough and cleanup (2 to 3 hours). We tension-check the fabric, pull any digging spoil back over the post holes, and walk the line with you before we leave. If Kennedale’s inspection is required for your scope, that happens here or the following business day, depending on how the city’s schedule is booked.
Total elapsed time from signed estimate to finished fence is usually 5 to 10 business days once material is ordered. That’s slower than the crew’s actual install time because material has to land and the city’s own submittal clock has to run.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The choices you’ll make before we dig
- Gauge and coating. Standard residential chain link is 11.5 gauge wire with a galvanized finish. A heavier 9-gauge wire and a vinyl-coated finish (black, green or brown) both cost more but resist rust and look less industrial. On a property where you’re fencing in a working shop or a long rear lot line, 9-gauge is the honest recommendation.
- Post size and spacing. 2-3/8″ line posts at 10-foot spacing is standard; going to 8-foot spacing or heavier posts raises the price but stiffens the fence against a dog or a windy open lot. On an acreage property with a long exposed run, that extra stiffness is worth it.
- Height. 4-foot, 5-foot and 6-foot are the common residential heights. 6-foot is the usual pick for livestock containment or a property line with a neighbor; 4-foot is common for a front-yard boundary. Kennedale has no single fence height rule baked in across the city, so the answer depends on setback and any HOA overlay.
- Gate configuration. A single walk gate (usually 3 or 4 feet) plus a drive gate (10, 12 or 16 feet) is the standard combo. Double drive gates wider than 12 feet need heavier framing and bracing to stay sag-free, which is a real cost driver.
- Bottom tension wire and top rail. Both are upgrades that pay for themselves on any fence where animals or wind are a factor. We won’t talk you into them for a fence that doesn’t need them.
On a job where the fence is part of a full Fence Installation in Kennedale plan (say, chain link along the back line and something more decorative up front), we spec the whole thing together so the corners line up and the gate placements make sense.
What Chain Link Fence costs in Kennedale, TX

The short answer: $3,500 – $9,000 for a residential chain link fence in Kennedale, and that number moves with five variables. Here’s the breakdown we work from when we price a job in 76060.
| Line item | Typical range |
|---|---|
| Standard 4 – 5 ft chain link, 150 – 200 ft | $3,500 – $5,200 |
| 6 ft chain link, 200 – 300 ft | $5,000 – $7,800 |
| Vinyl-coated (black/green) upgrade | $600 – $1,800 more |
| Walk gate (3 – 4 ft) | $350 – $700 each |
| Double drive gate (10 – 16 ft) | $900 – $2,200 |
| Bottom tension wire add-on | $250 – $600 |
The five things that push a Kennedale job toward $3,500 versus $9,000: total linear feet (the biggest lever by far); gauge and coating (9-gauge and vinyl cost more but outlast 11.5-gauge galvanized); gate count and gate width (a wide double drive gate on a rear lot line adds real money); site conditions (a fence line through heavy brush, roots or a slope goes up); and whether Kennedale permitting or an HOA review is in scope. A written estimate from us is line-itemed, so you see every one of those separately. Our Fence Installation service covers the full range of fence types if you want to compare.
See the difference
Before
After
Before
After
Before
AfterWhat Kennedale homes specifically do to this job
Kennedale is a built-out city of roughly 8,000 people tucked between Arlington, Mansfield, Burleson and Fort Worth, and almost everything built here happens on lots that already exist. That changes the fence job in ways you notice. Because the city runs its own permitting and inspections rather than deferring to Tarrant County, the submittal and inspection rhythm is Kennedale’s own, and it doesn’t match what the crew was doing the day before in Mansfield or Arlington. On the larger lots where a detached shop or barndominium sits well back from the street, the fence line often has to work around a long utility run or a separate meter service, and the drive gate placement usually has to account for a rear driveway that wasn’t there when the lot was first built. Our clay soils are the other factor: they shrink and swell enough that post holes set shallow move within a season, so we go deep and wide. If you’re pairing the fence job with work on those outbuildings, homeowners often pair this with ADU Site Prep & Utilities in Kennedale to get the utility runs and slab elevations sorted first.
We cover the whole of Kennedale and the surrounding area, including the 76060 ZIP. Call (855) 912-5373 with your address and we’ll confirm the specifics for your lot before we quote.
Serving Kennedale, TX – Our Local Coverage Area
We serve Kennedale and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently asked – Chain Link Fence in Kennedale

Most chain link fences in Kennedale take 1 to 3 working days to install once material is on site, with total elapsed time from signed estimate to finished fence usually 5 to 10 business days. The gap is material lead time plus the city’s own permit-and-inspection schedule, which the crew can’t compress. Call (855) 912-5373 for a date estimate specific to your address.
It depends on the height, setback and whether an HOA overlay applies – because Kennedale runs its own permitting rather than deferring to Tarrant County, the answer comes from the city’s own submittal process, not a neighboring city’s rule. We confirm what’s required for your specific lot before we order material, and the estimate reflects any inspection scope. Call (855) 912-5373 and we’ll walk through your property details.
Yes, in most cases – we call 811 locates before we dig, and on larger Kennedale lots we work the fence line around buried utility runs to a rear shop or barndominium. If a post has to go in near a line, we adjust the post spacing or shift the line rather than risk a hit. Call (855) 912-5373 to schedule a free on-site estimate.
Residential chain link fence in Kennedale runs $3,500 – $9,000, with most jobs landing between $4,200 and $6,800. Our estimate is line-itemed and fixed for the scope we quote – no surprises at the end. Call (855) 912-5373 for your exact number.
Every chain link fence we install is backed by our 730-Day Done Right Promise – if the workmanship isn’t right, we make it right. That covers installation and tension, not damage from a storm or a vehicle, and it’s backed in writing. Call (855) 912-5373 with any questions before you sign.
Get a free chain link fence estimate in Kennedale
Call (855) 912-5373 for a free on-site estimate on a chain link fence in Kennedale. We’ll walk your property line with you, confirm utility locates, and put a line-itemed price in front of you before anything gets ordered. No pressure and no surprise line items – just a clear number and a date. If the fence is part of a bigger project, homeowners often pair this with Door Installation in Kennedale once the shop or outbuilding is framed out.
Written by the team at Groundwork Construction Co.












