







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Chain Link Fence in Fort Worth, TX: What the Job Actually Involves
A chain link fence in Fort Worth runs $3,500 to $9,000 for a typical residential install, and most yards are finished in one to three days once materials are on site. The work itself is straightforward: set galvanized posts in concrete, stretch the mesh, hang the gates. What separates a fence that stays tight for twenty years from one that sags by year three is post depth, tension, and how the soil behaves. Call (855) 912-5373 for a free on-site measurement and a written line-item quote.
How We Build a Chain Link Fence, Stage by Stage

Nobody’s chain link job is identical, but the sequence rarely changes. Here’s what each day looks like and where you make decisions.
Stage 1: Walk the line and check the ground (day of estimate)
We measure the run, flag utility locates, and check what’s already buried – existing sprinkler zones, gas risers, and the corners where a gate will swing. You decide the fence line and where the gates land. If it’s part of a full Fence Installation in Fort Worth that also includes a different style along the front, that scope gets sorted here.
Stage 2: Post layout and auger work (day 1)
Terminal posts get set deeper than line posts. Corners and gate posts take the most load, so they go in at roughly 30 to 36 inches, and line posts sit around 24 inches. Post spacing runs 8 to 10 feet on residential work. On Fort Worth’s clay, we widen the hole bottom slightly so the concrete bells out and resists frost heave and soil creep.
Stage 3: Concrete cure (day 1 into day 2)
Post holes get filled with a Sakrete or Quikrete fast-setting mix, and you wait. We don’t stretch mesh over green concrete. Depending on weather, that’s 24 to 48 hours. In a July heat wave the mix sets faster; after a wet spring week, it takes longer. This is the single biggest reason a fence takes three days instead of one.
Stage 4: Rails, mesh, and tension (day 2 or 3)
Top rail gets threaded, the tension bar takes the fabric, and the winch pulls it tight. Gate posts get double-checked before the gates hang. You’ll walk the line with us and decide whether the gate hardware is standard or upgraded.
Stage 5: Final walkthrough (same day)
We check every tie, confirm gate swing and latch, and clean up the concrete splash at the post bases. Most residential jobs are done in a single visit after the cure window. You get the walkthrough and the warranty paperwork.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Chain Link Options You’ll Actually Choose Between
Most of the decisions happen before we ever dig a hole. These are the ones worth thinking through.
- Mesh gauge and coating. Wire comes in 11.5-gauge (standard residential) and 9-gauge (heavier, holds tension longer). Galvanized is the baseline; vinyl-coated in black or green costs more but blends into a treeline and holds up to sun better.
- Post schedule. 2 3/8-inch line posts are the residential norm. Upsizing to 2 7/8-inch on corners and long runs adds rigidity where wind load is highest.
- Height. 4 feet for pet containment, 5 feet for a standard privacy-adjacent run, 6 feet where HOA rules or insurance allow. Taller costs more per linear foot.
- Fabric options. Standard chain link is open. Privacy slats, windscreen, and topped rails turn it into a screen. Slats in the Fort Worth sun fade, so pick a UV-stable color if you go that route.
- Gate style and operators. Walk gates in 3-foot or 4-foot widths, drive gates from 10 to 16 feet. Swing or slide. If you want automation later, the gate post and operator pad need to be planned now, not retrofitted.
What a Chain Link Fence Costs in Fort Worth, TX

Residential chain link in Fort Worth lands between $3,500 and $9,000 for most single-family properties. Here’s what pushes a job toward one end or the other:
| Line Item | Typical Range |
|---|---|
| Standard 4 – 5 ft chain link, per linear foot | $18 – $32 |
| 6 ft with privacy slats, per linear foot | $30 – $55 |
| Walk gate, installed | $250 – $600 |
| Drive gate, installed | $700 – $1,800 |
| Full residential install (150 – 300 linear ft) | $3,500 – $9,000 |
The variables that matter most: total linear footage, whether the ground is level or sloped, how much old fence has to come out, the gauge and coating you pick, and whether a gate needs automation. A clean 150-foot run on a flat lot comes in near the low end. A sloped 300-foot lot with three gates, haul-off, and privacy slats pushes the high end. A written estimate from us lists each line – materials, labor, concrete, haul-off, gates – so you can see exactly where the dollars go. Most jobs here come back to the same few unknowns: hidden roots, buried debris, and old posts encased in concrete that need extraction.
See the difference
Before
After
Before
After
Before
AfterWhat Fort Worth Homes Specifically Do to a Chain Link Fence
Fort Worth is a two-speed city, and that shows up on fence jobs more than most trades. In Fairmount and Ryan Place, the early-1900s Craftsman and bungalow blocks sit on pier-and-beam foundations, and the fence line often runs over old brick walkways, former carriage-house pads, and roots around mature pecans and live oaks. In the fast-growing northwest toward Alliance and Walsh Ranch, we’re working brand-new slab lots where the topsoil is thin and the fill is fresh. Both neighborhoods demand different post schedules and different dig methods.
The real Fort Worth factor is the black clay. It swells when wet and shrinks hard in summer, and that movement is what sags a poorly set post within a few seasons. We set deeper and bell out the base. On the design-review overlays in Fairmount, Ryan Place, and the Stockyards, even a simple fence replacement can pull into a district review, so plan for added weeks on permits there. In Haltom City, Saginaw, and Richland Hills, the rules are less strict but the clay is the same. Homeowners who pair a new run with other exterior work often also plan ADU Site Prep & Utilities in Fort Worth at the same time, since trenching and grading overlap. And when a gate opener or entry feature ties into the house, they sometimes line up Door Installation in Fort Worth alongside it.
Serving Fort Worth, TX – Our Local Coverage Area
We serve Fort Worth and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked: Chain Link Fence in Fort Worth

Most residential chain link installs are finished in one to three working days. The concrete cure is the longest stretch: posts go in day one, mesh usually follows 24 to 48 hours later. Call (855) 912-5373 for a schedule estimate on your property.
It depends on height, setback, and district. Fort Worth residential fences generally don’t need a permit up to six feet on typical lots, but historic-district properties (Fairmount, Ryan Place, the Stockyards area) can require design review even at standard height, and HOA rules run stricter than the city. We confirm the requirement for your address before we schedule. Call (855) 912-5373 to sort it out.
Yes, in most cases. We auger at each post point, so the impact is a small hole every 8 to 10 feet, not a full excavation. Sprinkler heads get flagged and worked around. The one thing we won’t promise is zero damage – any crew that does is guessing. Call (855) 912-5373 to walk your yard.
Typical residential installs run $3,500 to $9,000, depending on linear footage, height, gauge, and gates. Per-foot pricing falls between $18 and $32 for standard 4-5 ft and $30 to $55 with privacy slats. Call (855) 912-5373 for a free written quote.
Every chain link install we do is covered by our 730-Day Done Right Promise: if it’s not done the way we said it would be, we come back and make it right. Concrete settling and gate hardware are covered. Call (855) 912-5373 with any warranty question before you sign anything.
Get a Free Chain Link Fence Estimate in Fort Worth
Call (855) 912-5373 to set up a free on-site estimate for chain link fence in Fort Worth. A live person answers around the clock, and a technician comes out, measures the run, checks the ground, and hands you a written line-item quote. No high-pressure pitch. Our Fence Installation team works the full Fort Worth area, including Fort Worth proper and the neighboring suburbs. If you’re comparing bids, that written quote gives you an honest number to measure against.
Written by the team at Groundwork Construction Co.












