







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Concrete Driveways & Concrete Work in Bedford, TX: What It Costs and What to Expect
Concrete driveway installation in Bedford runs $4,500 – $12,000, and a full tear-out and replacement lands at $5,000 – $14,000. Most driveways here take two to three working days of pouring and shaping, then about seven days before you drive a car on it. Call (855) 912-5373 and we’ll set a free on-site estimate. The rest of this page is what actually happens on a Bedford slab job, and what it costs when things go the way they should.
How a concrete driveway job runs, start to finish

The honest version, stage by stage. For an older Bedford driveway, most of the work is what you never see once the pour is done.
Stage 1: Site walk and measurements (day 1, about an hour)
We measure the existing driveway footprint, the slope from the garage apron to the street, and any separation between the slab and the garage floor. You’ll decide right here whether this is a replace or an overlay, and how much of the apron to take out. On older Bedford homes in ZIPs 76021 and 76022, we often find the original slab already cracked at the apron, which settles the question.
Stage 2: Tear-out, haul-off, and subgrade (day 1 to day 2, half a day to a full day)
A 20-foot-by-40-foot driveway means roughly 12 to 15 cubic yards of old concrete to break, load, and haul. For a typical 400-square-foot driveway, expect six to nine truckloads of concrete debris off the property. Once the old slab is gone, we look at what’s underneath. North Texas clay tells you what it’s doing, and if the base is saturated or has already heaved, that’s where the extra cost of over-excavation comes in.
Stage 3: Form setting and base preparation (day 2, about half a day)
Forms go up along both edges as well as the street apron. We set the base to a compacted depth that supports the slab you’re actually paying for, plus rebar or mesh laid on chairs so it doesn’t sit flat on the dirt. This is the day you’ll confirm expansion joint placement and whether you want control joints on a specific layout. Getting the joints right here matters far more than the finish you pick.
Stage 4: Pour and finish (day 3, three to four hours on the pour, then a cure window)
A 400-square-foot driveway is four to five truckloads of ready-mix. The pour happens in the morning, then we apply the broom finish or a textured surface while the edges are still workable. A stamped or exposed-aggregate finish adds a day of labor to the schedule. The slab then needs to be kept wet for about seven days, and you’ll stay off it with a vehicle for that week.
Stage 5: Curing, joint sealing, and final walkthrough
Joints get filled and sealed after curing so water doesn’t work its way into the cracks. We walk the finished slab with you, check the slope, and confirm everything drains away from the home. Groundwork backs this work under our 730-Day Done Right Promise, which means if a structural crack shows up in that window, it gets fixed.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The options you’ll choose between for a Bedford pour
- Broom finish vs. exposed aggregate: A broom finish is standard, holds grip, and costs the least. Exposed aggregate reveals the stone and hides wear better over the years, but adds labor and isn’t as easy to repair cleanly.
- Standard gray ready-mix vs. a color hardener: Plain gray is the cheapest and most repairable. A color hardener runs 15 to 20 percent more and makes future patches harder to match, which matters on a driveway that takes hail and sun.
- Rebar vs. welded wire mesh: Rebar costs a few hundred dollars more on a typical driveway but holds the slab together across the clay movement that’s common here. For anything over 400 square feet, rebar is the honest choice.
- Full replacement vs. overlay or vertical raise: A full replacement is usually the right answer for a cracked, heaving slab. An overlay is cheaper but only works if the base underneath is intact, and in older Bedford homes it usually isn’t.
- Joint layout and expansion-board placement: This is where a bad job shows up in year three. The joint plan is part of what you’re paying for, and it should be drawn before the pour, not decided on the day.
What Concrete Driveways & Concrete Work costs in Bedford, TX

Concrete driveway installation in Bedford runs $4,500 – $12,000 for a typical residential driveway. A full replace, where the old slab comes out and a new one goes in, runs $5,000 – $14,000. What pushes a job toward the top of that range usually comes down to five things:
- Size: More square footage means more concrete, more rebar, and more truckloads to haul.
- Existing slab condition: A cracked, heaved, or badly draining slab means more tear-out and more base work under the new one.
- Drainage and grade correction: If the driveway slopes back toward the garage, we correct the grade before pouring or the water problem returns.
- Finish and material grade: Stamped, exposed aggregate, or colored concrete all cost more than a standard broom finish.
- Permits and utility locate: Any permit the work requires plus the utility locate is part of a written estimate, not a surprise add-on later.
Every written estimate is line-item and fixed. The number you see is the number you pay, unless you change scope mid-job, and there are no change orders sneaking in on pour day. Call (855) 912-5373 for an exact quote on your driveway.
See the difference
Before
After
Before
After
Before
AfterWhat Bedford’s older housing stock does to this job
Bedford is a built-out mid-cities suburb. There’s essentially no undeveloped land left here, so almost every concrete driveway project in Bedford is a renovation, not new construction. The homes in ZIPs 76021 and 76022 were mostly built between the 1960s and 1980s, and their original driveways are right at or past the end of their service life. That older slab was likely poured with shallower throat and thinner edges than what current code expects, and it’s been sitting on expansive clay through a few dozen North Texas summer-heat cycles. When we pull one out, we almost always find the failure started at the joints, not the surface: water got in, worked down around the clay, and lifted the edge.
Because Bedford’s stock is older, the driveway job here also tends to sit inside a larger set of improvements. Homeowners on a 1960s ranch often pair a new driveway with foundation drainage or a re-roof, which you can see on our Driveway & Pavers in Bedford page. If the plan includes a new garage door or entry, we handle that alongside the concrete, which is why a driveway job here often becomes a Door Installation in Bedford conversation once the slab is settled. And if a backyard ADU is on the list, homeowners often pair the concrete apron with ADU Site Prep & Utilities in Bedford, so the access and utility trenching are worked out together. Whether the pour is part of our Driveway & Pavers service or a standalone concrete job, we treat the concrete as the foundation everything else sits on.
Serving Bedford, TX – Our Local Coverage Area
We serve Bedford and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently asked: Concrete Driveways & Concrete Work in Bedford

A standard driveway runs two to three working days from demo to pour, plus about seven days of stay-off curing before you park a car on it. Stamped or exposed-aggregate finishes add a day of labor. If the base needs over-excavation or drainage correction, add another day. Call (855) 912-5373 to get your specific timeline in an estimate.
Any new or reconstructed driveway in Bedford should be checked against the city’s established code and permit process, especially when it changes the street apron or slope. Because the city is fully built out, work here goes through the established inspection process rather than a new-subdivision approval. We pull the permits and handle inspections as part of the quote. Call (855) 912-5373 and we’ll confirm what your project needs.
Only if the base underneath the old slab is still solid and the existing concrete hasn’t cracked or heaved. On a Bedford driveway from the 1960s or 1970s, that base often isn’t intact after 50+ years on clay. We’ll tell you honestly on the site visit whether an overlay or a full replace is the right call. Call (855) 912-5373 for a free estimate.
Demo and haul-off, base preparation, rebar or mesh, the pour, finish and joints, joint sealing, and any permits or utility locates. Concrete pricing in Bedford ranges from $4,500 – $12,000 for a standard install and $5,000 – $14,000 for a full replacement. The line items are fixed before work starts. Call (855) 912-5373 for an exact quote.
Every concrete driveway we pour is covered by our 730-Day Done Right Promise, so if there’s a structural failure tied to the work in that window, we come back and fix it. That’s backed in writing, not just talked about. Call (855) 912-5373 to talk through the warranty on your project.
Get your free concrete estimate in Bedford
Start with a free on-site estimate. We come out, measure the existing slab, check the base and drainage, and give you a written line-item quote for concrete driveways & concrete work in Bedford. Calls are answered by a live person, 24/7, so you don’t wait until Monday morning. Reach us at (855) 912-5373. If you’re near Hurst, Richland Hills, North Richland Hills, or Watauga, we cover those too through our Bedford service area.
Written by the team at Groundwork Construction Co.












