







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Chain Link Fence in Benbrook, TX: What It Costs and How Long It Takes
A chain link fence in Benbrook, TX typically runs $3,500 to $9,000 for a standard residential lot, and most jobs are measured, permitted and set in two to four working days. You’re buying galvanized or vinyl-coated steel, set in concrete footings, with posts sized to your wind and soil conditions. Exact cost depends on linear feet, height, gauge, gates and how much old fencing has to come out first. Call (855) 912-5373 for a free on-site estimate.
How a Chain Link Job Actually Runs, Start to Finish

Chain link isn’t complicated, but the sequence matters more than most homeowners expect. Skip a stage and you get sagging top rail or posts that lean after the first hard rain. Here’s what the days look like when we run this job in Benbrook.
Stage 1: Site walk and measurement (day one, about an hour)
We mark the proposed line, check the property corners, and confirm the footage. This is where you decide fence height (4, 5 or 6 ft), gauge, and whether you’re leaving room for a future gate. We also look for buried irrigation, sprinkler lines, and any utility flags already on the lot. If a survey is missing, you’ll need one before posts go in at the property line.
Stage 2: Demo and layout (day one, half day)
Old fence panels, posts and concrete footings come out. Pulling posts set in concrete is the slow part, and it’s the single biggest swing in labor on a Benbrook job – a clean vinyl removal runs faster than 30-year-old steel sunk in clay. Layout string goes up next so every post lands on line and on grade.
Stage 3: Post setting and concrete cure (day one into day two)
We dig holes to depth, set terminal and line posts, and pour concrete footings. Posts need to cure before tension goes on. In North Central Texas heat, that cure window is real – rushing it and pulling wire the same afternoon is how fences end up out of plumb in July.
Stage 4: Rails, mesh and tension (day two to three)
Top rail and brace bands go on, then mesh is stretched and tied off. This is where gauge and coating show their quality. Tensioning a light 11.5-gauge mesh on a long run takes longer and needs more ties than a heavier 9-gauge.
Stage 5: Gates, walkthrough and cleanup (days three and four)
Gate frames get hung, latches aligned, and the swing checked. We walk the run with you, pull the off-cuts and spoil, and hand off the written summary. Permits and inspections follow your city’s schedule.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Chain Link Options You’ll Actually Choose Between
Most of the decisions happen at the estimate, and they don’t all point the same way. Here’s what moves the quality and the price.
- Gauge (wire thickness): 11.5-gauge is the budget standard and fine for light use. 9-gauge holds up far better on long runs, in wind, and around kids and dogs. The step up costs more per foot and is worth it on anything over 150 feet.
- Coating: Bare galvanized steel is cheapest and performs well in dry stretches, but it dulls. Vinyl-coated (black, green, brown) costs 15-25% more and holds color through the heat, plus it reads cleaner against landscaping.
- Height: 4 ft for boundary marking, 5 ft for pet containment, 6 ft where you want more separation. Each step up raises post and mesh cost.
- Posts and top rail: Standard is round schedule-20 pipe; heavier schedule-40 is the upgrade. Terminal posts and braces carry the tension, so don’t skimp there even if you economize on mesh.
- Gates: Walk gates vs. drive gates change the frame, hinges and latch. A wide drive gate on a chain link run needs a stiffer frame than a pedestrian gate.
- Finish systems: For a residential look on a budget, chain link with privacy slats or a screen is a middle path. Where the material aesthetic matters more, our Fence Installation in Benbrook scope covers the full range of fence types.
What Chain Link Fence Costs in Benbrook, TX

Most Benbrook chain link jobs land between $3,500 and $9,000. That’s the number to budget against, and the wide band is a function of the five factors below, not guesswork.
- Linear feet: The single biggest driver. A small backyard run sits near the bottom; a full perimeter with multiple corners sits near the top.
- Height and gauge: A 4 ft 11.5-gauge run is the low end; 6 ft 9-gauge vinyl-coated is the high end.
- Removal condition: Existing posts set in concrete, overgrown runs, or old steel are the most common reason a job climbs.
- Gates: Each gate adds hardware, framing and labor; drive gates add the most.
- Site access and grade: Sloped or tight lots slow digging and post setting, and Benbrook’s clay can change how deep holes need to go.
A written estimate itemizes footage, gauge, coating, post schedule, gate count and demo. Verify what’s excluded: stump grinding along the line, survey, and utility relocation are often separate. Our pricing is upfront with no change orders once the scope is signed, and every job carries the 730-Day Done Right Promise.
See the difference
Before
After
Before
After
Before
AfterWhat Benbrook Lots and Benbrook’s Own Permit Office Do to This Job
Benbrook isn’t a Fort Worth subdivision with a Fort Worth permit counter. The city runs its own permit office and inspection expectations, and much of the work here is infill and rebuild on scattered lots near the lake and the older Benbrook core rather than large single-tract builds. That matters for a fence: a chain link run on a lot line near Lake Benbrook and the Trinity corridor gets reviewed with an eye on drainage and setbacks, and a stretch along the flood-prone corridor is worth checking before posts go in. Expansive blackland clay is the other constant. It swells and shrinks with the seasons, so a post hole that’s adequate on a Fort Worth sand lot may need to go deeper here to hold plumb through a dry stretch. We set to depth and concrete accordingly. Our Benbrook service area covers ZIP 76116 and the surrounding blocks.
Serving Benbrook, TX – Our Local Coverage Area
We serve Benbrook and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Chain Link Fence in Benbrook

Most residential runs take two to four working days from demo to final walkthrough, with a concrete cure window between post setting and tensioning. Larger perimeters, removal of old steel footings, or drive gates push toward the four-day end. Call (855) 912-5373 for a timeline on your specific lot.
Benbrook has its own permitting process, and many residential fence installations require one depending on height and location. We pull the permit and schedule the inspection as part of the job so you aren’t chasing the counter. Call (855) 912-5373 to confirm what your lot needs.
Usually yes. We layout around existing irrigation and mark utility lines before digging, and a fence run rarely disturbs structures. Only where a post crosses a buried line or a gate needs a structural post do we have to adjust. Call (855) 912-5373 and we’ll walk the line with you.
A typical Benbrook job runs $3,500 to $9,000 depending on footage, gauge, coating, gates and demo. The written estimate itemizes each of those so you see exactly where the money goes. Call (855) 912-5373 for a free on-site quote.
Every chain link job we run is backed by the 730-Day Done Right Promise – if it’s not done right, we make it right. That covers workmanship on posts, tension and alignment, on top of the material manufacturer’s warranty. Call (855) 912-5373 with questions before you sign anything.
Get a Free Chain Link Fence Estimate in Benbrook
We’ll walk your property line, measure the footage, check for buried lines and setback issues, and hand you a written, itemized estimate for your chain link fence in Benbrook. No pressure, no vague numbers. Call (855) 912-5373 to schedule – calls are answered by a live person around the clock. A live conversation gets you a real number and a real start date. Homeowners often pair this work with a full project scope, and our Fence Installation and Door Installation in Benbrook crews cover the finishes of the same build. For outbuilding work, we also handle ADU Site Prep & Utilities in Benbrook.
Written by the team at Groundwork Construction Co.












