







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Chain Link Fence in Azle, TX: What It Costs and What the Job Involves
A chain link fence in Azle, TX typically runs $3,500 to $9,000, depending on footage, height, gauge, and how much site work the ground needs before posts go in. Most residential jobs here are finished in one to three days once materials are staged and lines are marked. Call (855) 912-5373 and we’ll set a free on-site estimate so you’re pricing your actual fence line, not a ballpark over the phone.
Key takeaways
- Azle chain link fence pricing lands in the $3,500 – $9,000 range for most acreage and subdivision lots.
- Installed on most properties in one to three days; acreage runs are scheduled over multiple days.
- Two-county permitting applies across ZIPs 76020 and 76098, and we pull the permits.
- Galvanized is the budget workhorse; vinyl-coated lasts longer against North Texas sun and clay.
How We Build a Chain Link Fence in Azle, Start to Finish

Every job we run follows the same five stages, and you’ll know what’s happening at each one before we knock on your door.
Stage 1: On-site measure and layout (same day as the estimate)
We walk the property line, confirm corners and gate locations with you, and check where utilities run. On acreage tracts in Azle outside the newer subdivisions, that means locating the septic field and well head before a single post is set. You decide here on fence height, gauge, gate count, and whether you want privacy slats later. This visit takes about 45 minutes for a typical quarter-acre to one-acre lot.
Stage 2: Permits and utility locates (day 1 to day 5)
We pull the fence permit and request utility locates through the 811 system so nobody drives a post through a water line or buried electrical. Acreage properties with well systems and private septic take a little longer to clear because the owner holds the records, not the city. You don’t have to chase anything; we handle the paperwork and tell you the day work starts.
Stage 3: Demo and ground prep (day 1 of install)
If there’s an old fence coming out, we tear it down, pull posts, and haul the material off in the same visit. Then we mark the line and dig post holes on 8-foot centers, going deeper on corners and gates for stability. That haul-off alone is a decent chunk of the value in the price.
Stage 4: Posts, rails, and mesh (day 1 to day 2)
Posts get set in concrete and cured, then top rail and tension bands go up, then the chain link mesh is stretched and tied. A standard residential job is a two-person crew and takes a full day for the posts and hardware, mesh on the second. On longer runs across a bigger Azle tract, expect both days to stretch and possibly a third.
Stage 5: Gates, tension, and walkthrough (day 2 or 3)
We hang the walk gate and any drive gates, tension everything, and walk the full line with you. You get to pull on it, open and close every gate, and check the sight lines. If something’s not right, it gets fixed before we leave.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Options You’ll Actually Choose Between
A chain link fence isn’t one product. These are the spec decisions that drive the final number:
- Gauge: 11.5-gauge is the residential standard and balances cost with holding up against kids, dogs, and weather. 9-gauge is heavier and costs more, but on acreage where the fence has to survive livestock pressure or heavy storm activity, it’s the smarter pick.
- Coating: Bare galvanized steel is the lower-cost option and holds up fine, but it shows every weather mark. Vinyl-coated mesh (black, green, brown) costs roughly 15 – 25% more and lasts longer against the North Texas sun and clay-soil moisture.
- Height: 4-foot is typical for yard boundary. 5- and 6-foot runs add cost per foot but matter for dog containment and privacy screens.
- Gates: A standard 4-foot walk gate is included in most quotes. Drive gates come in single or double and add real cost, especially on wide acreage driveways.
- Privacy slats: Optional, add a per-foot cost, and turn a chain link fence into a semi-private barrier. Good compromise on lots where the budget doesn’t stretch to a full privacy fence.
- Terminals and corners: Every corner, gate post, and end post needs a heavier post and concrete set. More turns mean more cost.
What Chain Link Fence Costs in Azle, TX

For a typical Azle residential job, expect $3,500 to $9,000 installed. That covers standard residential runs on a quarter-acre to one-acre lot. Here’s what moves the number to the low end versus the high end:
- Linear footage: A small backyard perimeter sits near the bottom of the range. An acreage boundary run pushes to the top and past it.
- Height and gauge: 4-foot 11.5-gauge is the budget driver; 6-foot 9-gauge with vinyl coating is the top of the residential range.
- Gate count: One walk gate is standard. Multiple or oversized drive gates add real money.
- Ground conditions: Rocky ground, heavy clay, or an old fence to remove and haul pushes the price up. Clean, level ground keeps it low.
- Permit scope: Azle straddles Parker and Tarrant counties, so the permit path depends on the parcel. We pull it as part of the written quote, not as a surprise line item later.
A written estimate lists footage, height, gauge, coating, gate count, post spacing, concrete, haul-off, and permits. What it won’t cover unless we spell it out: cutting through existing concrete, retaining walls for slope, or utility relocation. We quote those separately up front so the number on the page is the number you pay.
See the difference
Before
After
Before
After
Before
AfterWhat Azle Homes Specifically Do to This Job
Azle sits on the western edge of the DFW metro, split across Parker and Tarrant counties, with a mix of older rural ranch and manufactured homes on acreage and a wave of new custom builds in the subdivisions around Eagle Mountain Lake and along the FM corridors. That mix changes fence work here in ways it doesn’t in a uniform suburb. On acreage tracts, we’re often dealing with well and septic systems before we can dig, and pipe fence corners and gate posts need deeper concrete sets than a standard residential job because the runs are longer and catch more wind.
Lakefront and near-lake lots bring their own considerations: drainage patterns and clay-soil movement along the shoreline can shift posts if the ground isn’t prepped correctly, so we set terminals deeper on those runs. Newer subdivision lots in ZIPs 76020 and 76098 are more predictable slab-adjacent ground, but HOA rules in those communities often dictate fence height and color, so we check that during the estimate. Older ranch properties on the outlying tracts often have an existing fence that’s rusted through its base where clay moisture has sat against the posts, and that haul-off is part of the scope.
Serving Azle, TX – Our Local Coverage Area
We serve Azle and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked: Chain Link Fence in Azle

Most Azle residential jobs take one to three days from the day materials arrive. Standard quarter-acre to one-acre runs finish in a day and a half to two days, while acreage boundaries with multiple gates can push to three or four. The permit and utility locate stage adds up to a week before installation starts, and we tell you the exact start date up front.
Yes, in most cases. Azle’s permits run through two counties depending on the parcel (Parker and Tarrant), and the requirements differ. We pull the permit as part of the written estimate so nothing lands on you mid-project. If your lot is in a lakeside HOA, we also check their height and material rules during the estimate visit.
Yes. We locate the well head and septic field before digging, and if the fence line crosses a drain field or a buried line, we adjust the line or reroute around it. On acreage properties, that’s often the first conversation we have, and it’s why the on-site estimate matters so much more than a phone quote.
Most residential jobs run $3,500 to $9,000 installed, driven by footage, height, gauge, coating, and gate count. Acreage runs with multiple drive gates push toward the high end and beyond. Call (855) 912-5373 for an exact quote – estimates are free and we come to the property.
Every chain link fence we install is backed by our 730-Day Done Right Promise. If a post pulls, a gate sags, or the installation isn’t right, we come back and fix it. Materials carry their manufacturer warranty on top of that, and we walk you through what’s covered before you sign anything.
If your chain link fence is part of a Fence Installation in Azle project that also includes other fencing or a full boundary build-out, we’ll size the whole job in one estimate. Lake-lot owners often pair this with ADU Site Prep & Utilities in Azle when they’re bringing utilities to a new structure, and homeowners upgrading outbuildings often add Door Installation in Azle on the same visit. For the wider service picture, see our Fence Installation hub or check the broader Azle service area to see what else we cover.
Ready for a Chain Link Fence in Azle? Get a Free Estimate
Call (855) 912-5373 to schedule a free on-site estimate for your chain link fence in Azle. We’ll walk the property, confirm footage, height, gauge, and gate count, check for well and septic, and hand you a written line-item quote with permits included. A live person answers, day or night. No-hassle upfront pricing, and 0% financing for 18 months if you need it. Most jobs are quoted on the spot.
Written by the team at Groundwork Construction Co.












